Types of Doors

The function of a door is to give access to building and to different parts of the building and to deny the access whenever necessary. Number of doors should be minimum possible. The size of the door should be of such dimension as will facilitate the movement of the largest object likely to use the doors.

In case of the residential buildings, the size of the door should not be less than 0.9 m × 2.0 m. Larger doors may be provided at main entrance to the building to enhance the aesthetic view. Minimum sized doors are used for bath rooms and water closets. The size recommended is 0.75 m × 1.9 m. As a thumb rule height of door should be 1 m more than its width.

Types of Doors

Various types of doors are in use which may be classified on the basis of arrangement of shutters, method of constructions, principles of working operations and materials used. Commonly used doors are briefly explained below:

Battened and Ledged Doors

Battens are 100 mm to 150 mm wide and 20 mm thick wooden boards. Their length is that of door opening. The battens are connected by horizontal planks, known as ledges of size 100 to 200 mm wide and 30 mm thick. Usually three ledges are used one at top, one at bottom and the third one at mid-height. This is the simplest form of door and the cheapest also. Battens are secured by tongued and grooved joint.

Figure 1. Battened and ledged door

Battened, Ledged and Braced Doors

If doors are wide apart from using battens and ledges diagonal members, known as braces, are provided to strengthen the door. Figure 2 shows a typical battened, ledged and braced door.

Sometimes above two types of shutters are provided within wooden frame work and in those cases they may be called as battened, ledges and framed doors.

Fig. 2. Battened, ledged and braced door

Framed and Panelled Doors

This type of door consists of vertical members, called styles and horizontal members called rails. The styles and rails are suitably grooved to receive panels. The panels may be of wood, A.C. sheet, glasses etc. The panels may be flat or of raised type to get good appearance. These are very commonly used doors. They may be of single shutter or of double shutter. Figure 3 show few types of panelled doors. If glass panels are used they may be called as glazed doors.

Fig. 3. Panelled and lazed doors

Flush Doors

The shutters of these doors are made of plywood or block boards. They are of uniform thickness. These shutters are available with different attractive vineer finishes. The time consumed in making such doors at site is quite less. These doors are suitable for interior portion of a building. Nowadays flush doors are commonly used in residential and office buildings. Figure 4 shows typical flush door.

Fig. 4. Flush door

Louvered Doors

Whenever privacy as well as ventilation is required such doors can be used. Louvers are the glass, wooden or A.C. sheet strips fixed in the frame of shutter such that they prevent vision but permit free passage of air. The doors may be fully or partially louvered. Such doors are commonly used for public bathrooms and latrines. [Fig. 5]

Fig. 5. Louvered door

Revolving Doors

It consists of a centrally placed pivot to which four radiating shutters are attached. The central pivot is supported on ball bearing at the bottom and has a bush bearing at the top. The shutters may be partly or fully madeup of glass. A circular space of entrance is provided within which shutters rotate.

As shutters rotate they give entrance on one side and exit on other side. These doors are preferred in public buildings like stores, banks, hotels, theatres where continuous use of doors is necessary. They are very much required in entrance to air conditioned public buildings. Figure 6 shows a typical revolving door.

Fig. 6. Revolving door

Swing Doors

Swing door has its shutter attached to the frame by means of double action springs. Hence shutter can move both inward and outward. They may be single shuttered or double shuttered. Such doors are preferred in offices and banks. Since these doors can open on both sides it is desirable to provide glass panels or peep holes to enable user to see the persons from other side. [Fig. 7]

Fig. 7. Plan of swing door

Sliding Doors

In this type of doors, shutter slides on the sides. For this purpose runners and guide rails are provided. Sliding shutters may be one, two or even three. Such doors are used in banks, offices etc. The arrangement of such shutters in plan is shown in Fig. 8

Fig. 8. Plan of sliding door

Collapsible Doors

Steel channels 16 to 20 mm wide are used as verticals. They are placed with 12 to 20 mm gap. Steel flats 16 mm to 20 mm wide and 5 mm thick are hinged to them as shown in Fig. 9. The rollers are provided at their top as well as at bottom so that shutter can be pulled or pushed side ways with slight force.

Fig. 9. Collapsible steel door

There may be single or double shutters. Usually these doors are used for additional safety. They are commonly used for front doors, bank locker rooms, school and college entrance doors.

Table 1. Difference between collapsible and revolving doors.

Rolling Shutters

Figure 10 show a typical rolling shutter door. It consists of a frame, a drum and a shutter made of thin steel plates. The width of the door may vary from 2 to 3 m. The shutter moves on steel guides provided on sides and can easily roll up. For this counterbalancing is made with helical springs on the drum.

Fig. 10. Rolling shutter

The shutter can be easily pulled down. These types of doors are commonly used as additional doors to shops, offices, banks, factory, buildings from the point of safety.

Leave a Comment

Your email address will not be published. Required fields are marked *